Produkte

Importierte PVA-Schwammrolle

Facebook
Twitter
LinkedIn

Importierte PVA-Schwammrolle zur Wasseraufnahme und zum Abwischen von Stellen nach der Leiterplattenreinigung oder vor der Heißlufttrocknung.
Importiertes PVA + PVC-Rohr und 8-10-fache Wasseraufnahme;
Schimmelresistent und fusselt nicht;
Schwillt nach dem Einweichen um 3-5 mm an.

Produktdetails

Produktübersicht

The imported PVA sponge roller absorbs and wipes residual water from PCB surfaces after cleaning or before hot-air drying. Its absorbent surface contacts the board at a suitable position in the line, helping remove water before the next processing stage.

The roller combines imported PVA sponge material with a PVC pipe. Customized sizes are available to match equipment dimensions, roller spacing, and the required contact arrangement.

Produktspezifikationen

Artikel Spezifikation
Produktname Imported PVA sponge roller
Material Importiertes PVA + PVC-Rohr
Hauptfunktion Wasseraufnahme und Oberflächenreinigung
Einbauposition Nach der Reinigung oder vor dem Trocknen mit Heißluft
Wasseraufnahme 8-10 times water absorption
Swelling After Soaking 3-5 mm
Aufgeführte Merkmale Mold-resistant and non-shedding
Größe Customized size available

Hauptmerkmale des Produkts

– Imported PVA sponge provides the absorbent working surface, supported by a PVC pipe. Confirm the complete mounting configuration against the machine drawing or existing sample.

– The listed water absorption is 8-10 times. Confirm the measurement basis and test conditions when comparing this figure with another roller specification.

– Wiping complements water absorption where the roller contacts the board. Alignment, surface condition, and suitable contact affect the result in the line.

– The sponge is described as mold-resistant and non-shedding. Regular cleaning and inspection remain important for keeping the working surface suitable for use.

– The listed dimensional change after soaking is 3-5 mm. Confirm how this change is measured and allow for the actual prepared dimensions when checking clearance.

– Customized size is available, and diameter and density can be selected with reference to line speed and roller spacing.

Function in PCB Processing

After cleaning, residual water moves with the board toward the next module. An absorbent roller provides a contact position where water can be taken up and wiped from the surface. The amount removed depends on the incoming water load, roller contact, alignment, and surface condition.

The roller can be used before hot-air drying where the machine layout provides an appropriate position. Final drying also depends on the downstream equipment and operating conditions.

Typische Anwendungen

– Water absorption after PCB cleaning

– Surface wiping at a matched position in PCB wet-processing equipment

– Residual-water removal before hot-air drying

– Replacement of an existing absorbent roller matched to the line

Imported PVA Material and Soaking

The sponge uses imported PVA material with a PVC pipe. When ordering, confirm the required material and roller construction together with the mounting dimensions. Imported material describes the PVA sponge; the pipe is specified separately.

The listed swelling after soaking is 3-5 mm. Confirm whether the stated change refers to diameter or another dimension and establish whether ordered measurements apply before or after soaking. Confirm the preparation procedure, soaking time, and water temperature for the supplied roller before installation.

Customization and Equipment Matching

Provide the outside diameter, working-face length, overall length, PVC pipe dimensions, and shaft or bore arrangement. A drawing or sample helps check mounting points, clearance, and the relationship to adjacent rollers.

Provide line speed and roller spacing when discussing diameter and density. Also describe board thickness, contact arrangement, process liquid, and water load. Confirm the prepared working dimensions so that the roller can be fitted with suitable clearance and contact.

Auswahlleitfaden

Start with the process position and the function required at that point. Review the liquid contacting the roller, working temperature, and any chemical carryover with the supplier. Confirm compatibility for the actual application before selection.

Check the machine’s available roller space, mounting arrangement, and board path. The roller should contact the surface as intended without excessive compression or interference with adjacent components.

Installation und Wartung

– Isolieren Sie die Maschine gemäß ihrer Wartungsprozedur, bevor Sie die Walze ausbauen oder einbauen.

– Check the supplied dimensions, pipe, mounting arrangement, and sponge surface against the approved drawing or sample.

– Prepare the roller according to the supplier’s instructions and check its dimensions after preparation.

– Verify free rotation, alignment, clearance, and board contact using the equipment manufacturer’s setup procedure.

– Keep the sponge free from sharp debris and deposits. Use a cleaning method confirmed for the supplied roller and process conditions.

– Inspect for tears, uneven wear, contamination, or changes in water removal. Replace the roller when wear or damage affects its function.

Qualitäts- und Auftragsbestätigung

Agree the PVA material, roller dimensions, density, pipe and mounting details, and working-surface requirements against a drawing or sample. State whether dimensions are measured before or after soaking and confirm the preparation instructions for the supplied roller.

Qixingyuan Machinery supplies accessories for PCB processing equipment. Send the installation dimensions and operating conditions to discuss a replacement or customized size.

Verpackung und Lieferung

Confirm packaging and storage requirements for the supplied sponge roller. Protect the working surface from contamination, sharp contact, and concentrated pressure. Discuss quantity, destination, and delivery requirements during quotation.

Für ein Angebot benötigte Informationen

– Equipment model and intended roller position

– Outside diameter, working length, overall length, and dry or soaked measurement condition

– Abmessungen des PVC-Rohrs und Wellen- oder Bohrungsanordnung

– Liniengeschwindigkeit, Walzenabstand und Plattendicke

– Process liquid, working temperature, and water load

– Zeichnung, Muster oder Fotos der vorhandenen Walze und der Befestigungspunkte

– Quantity and delivery destination

Häufig gestellte Fragen

What material is used in this roller?

The sponge uses imported PVA material and the roller includes a PVC pipe. Confirm mounting details for the required configuration.

Where can this roller be installed?

It is intended for water absorption and wiping after PCB cleaning or before hot-air drying, subject to the equipment layout and process conditions.

Does the sponge swell after soaking?

Yes. The listed change is 3-5 mm after soaking. Confirm the measurement direction and wet dimensions before selecting roller spacing.

What does the water absorption figure mean?

The listed value is 8-10 times water absorption. Confirm its measurement basis and conditions with the supplier before comparing specifications.

Lässt sich die Größe anpassen?

Yes. Provide a drawing or sample with the diameter, working length, overall length, pipe dimensions, and mounting details.

Can it be used with my process liquid?

Provide the liquid type, concentration, temperature, and exposure conditions for compatibility review before ordering.

Produktvideo

Verwandte Produkte

EPDM Sponge roller
EPDM-Schwammrolle
PVA sponge roller 5-1
PVA-Schwammrolle
PVC sponge roller
PVC-Schwammrolle
PU sponge roller
PU-Schwammrolle

Eine Nachricht hinterlassen

Mit hochpräzisen und leistungsstarken Zubehörteilen für Leiterplattenanlagen unterstützen wir die globale Elektronikfertigungsindustrie bei der Erreichung einer effizienten Produktion.