Qixingyuan supplies PCB equipment consumables and replacement parts for wet-process and horizontal production lines, including filter cartridges, seal strips, sponge and brush rollers, and related transmission or spray-system components. This category helps maintenance and procurement teams match replacement parts to the equipment position, working liquid, temperature, dimensions, and operating conditions. Buyers can provide drawings, samples, or key specifications so Qixingyuan can identify a compatible material and configuration for the actual production line.
Start with the job at the installation point. After a final rinse, look for a sponge that picks up water without marking the panel. At a brushing station, choose the contact surface by the residue you need to remove and the finish you need to keep. In a circulation loop, match the filter to the particle size and flow rate.
| Material or construction | Where to use it | What makes it different | What to confirm |
|---|---|---|---|
| Rouleau en mousse PVA | Final clean-water rinse | High water uptake and soft contact help remove the water film before hot-air drying. | Pre-soak before use. Check the working diameter when wet. |
| Rouleau en mousse PU | Wiping at higher line speeds | Polyurethane recovers after compression as successive panels pass through the rollers. | Check rebound and water pickup at your line speed and roller gap. |
| Rouleau en éponge PP | Wiping after a weak acid or alkali stage | The polypropylene sponge resists swelling, which helps maintain the working gap. | Confirm the bath concentration and temperature. Check how much liquid carries into the next stage. |
| Rouleau en mousse PVC | Wet lines with frequent restarts | This PVC sponge can go into service without pre-soaking and maintains its size when wet. | Match the roller diameter and verify compatibility with the process liquid and cleaning agents. |
| Rouleau en mousse EPDM | Wiping after a plating rinse | The elastic rubber surface compresses against the panel to wipe away residual liquid. | Check the plating chemicals carried into the rinse and the contact pressure the finish can tolerate. |
| Nylon filament brush | Brushing away particles and loose residue | Filament diameter and packing density determine how firmly the brush scrubs. | Specify the residue and panel finish. Check for brush marks on a sample panel. |
| Nonwoven brush roller | Surface preparation where finish matters | A continuous fibrous surface distributes contact across the panel. The grade determines the cutting action. | Match the grade to the required finish. Test at production speed and contact pressure. |
| Abrasive grinding roller | Removing oxide before further processing | Abrasive contact removes more surface material than routine cleaning requires. | Specify the oxide to remove and the maximum acceptable removal of underlying copper. |
| Pleated PP cartridge | Fine filtration at a specified flow rate | Pleats provide more filter area within the cartridge diameter. | Compare pressure drop at the required flow and micron rating. Match the end fitting and seal. |
| Melt-blown PP cartridge | Depth filtration of circulating process liquid | Bonded polypropylene fibers capture particles within the thickness of the filter. | Match the micron rating and cartridge dimensions. Check the allowable pressure drop. |
| String-wound cartridge | Prefiltration of liquids carrying suspended solids | Wound yarn traps particles through its depth. Available media include PP, cotton and glass fiber. | Specify both yarn and core materials. Check their compatibility with the liquid at operating temperature. |
For a replacement quote, send a photo or drawing and identify the process liquid, concentration and operating temperature. For rollers, include the outside diameter, working length and shaft or bore size. For cartridge or bag filters, include the housing model, element dimensions and micron rating.
PCB equipment consumables are used in cleaning, developing, etching, rinsing, plating, drying, conveying, and filtration sections of horizontal wet-process lines. Typical components support liquid filtration, panel transport, sealing, water retention, spray distribution, shaft support, and power transmission. The correct item depends on the equipment model, installation position, process liquid, operating speed, and maintenance objective; supplying these details helps match the replacement part to the line.
Fondée en 2011 sous le nom de Shenzhen Qixing Equipment Parts Business Department, notre entreprise se concentre sur les pièces détachées pour équipements de traitement humide PCB/LCD et les composants de remplacement personnalisés.
Une entreprise de haute technologie possédant de multiples certifications nationales de brevets technologiques.
Des lames d'air aux engrenages, vis et rouleaux de convoyeur, nous fournissons une gamme complète de consommables de transmission et de nettoyage.
Communication rapide via WhatsApp et e-mail pour les achats internationaux.